iglidur® X6 - material data

Table of contents

The most important specifications at a glance

Descriptive technical specifications
Wear resistance at +23°C- 🟧 🟧 🟧 ⬜️ ⬜️ +
Wear resistance at +90°C- 🟧 🟧 🟧 🟧 ⬜️ +
Wear resistance at +150°C- 🟧 🟧 🟧 🟧 🟧 +
Slide property- 🟧 🟧 🟧 ⬜️ ⬜️ +Coefficient of friction, dynamic, against steel: µ 0.09 - 0.25
Wear resistance under water- 🟧 🟧 🟧 🟧 ⬜️ +
Media resistance- 🟧 🟧 🟧 🟧 🟧 +
Resistant to edge pressures- 🟧 🟧 🟧 ⬜️ ⬜️ +
Resistant to shock and impact loads- 🟧 🟧 🟧 ⬜️ ⬜️ +
Dirt resistance- 🟧 🟧 ⬜️ ⬜️ ⬜️ +

When do I use this material?

  • If temperatures above +150°C occur
  • If the wear resistance of iglidur X is not sufficient during pivoting and rotation
  • If the press-fit is to be improved compared to iglidur X
  • If the maximum media resistance is required
  • If freedom from PTFE is required

When do I use a different material?

  • If you are looking for a cost-effective universal plain bearing -> iglidur G
  • If you are looking for a plain bearing for underwater use -> iglidur UW500, iglidur H370
  • If you are looking for a wear-resistant high-temperature plain bearing for linear strokes -> iglidur Z

Temperatures

min. application temperatureUpper application temperature, long-termUpper application temperature, short-termIn addition secure axially from
-100°C+250°C+315°C+165°C

Permissible surface speeds

Maximum surface speed [m/s]RotatingOscillatinglinear
Long-term1.51.15.0
Short-term3.52.510.0

Permissible pv values

Chart with logarithmic X and Y axes and a red line that starts flat and then declines.
Chart with logarithmic X and Y axes and a red line that starts flat and then declines.

Mechanical specifications

Graph with a red downward curve from 150 to 75 along the X-axis.
Graph with two rising lines for +23 °C and +60 °C.

Friction and wear

iglidur X6dryGreasesOilWater
Coefficient of friction μ0.09-0.250.090.040.04
Characteristic curve with a descending red line on the X and Y axes.
Chart with a red curve that drops sharply at first and then levels off around 0.08.

Shaft materials

Bar chart with categories A to G and bars of different heights.
Graph with two curves A and B on a coordinate grid; both rise, and B becomes much steeper from x=4.

Chemical resistance

MediumResistance
Alcohols+
Greases, oils without additives+
Hydrocarbons+
Fuels+
Strong alkalines+
Strong acids+
Diluted alkalines+
Diluted acids+

Moisture absorption

Chart with X and Y axes: a red line rises steadily.

Installation tolerances

Diameter d1 [mm]Housing H7 [mm]iglidur X6 plain bearing F10 [mm]Shaft h9 [mm]
up to 3+0.000 +0.010+0.006 +0.046 -0.025 +0.000
> 3 up to 6+0.000 +0.012+0.010 +0.058-0.030 +0.000
> 6 up to 10+0.000 +0.015+0.013 +0.071-0.036 +0.000
> 10 up to 18+0.000 +0.018+0.016 +0.086-0.043 +0.000
> 18 up to 30+0.000 +0.021+0.020 +0.104-0.052 +0.000
> 30 up to 50+0.000 +0.025+0.025 +0.125-0.062 +0.000
>50 to 80+0.000 +0.030+0.030 +0.150-0.074 +0.000
>80 to 120+0.000 +0.035+0.036 +0.176-0.087 +0.000
> 120 up to 180+0.000 +0.040+0.043 +0.203+0.000 +0.100

Thermal conductivity

Coefficient of thermal expansion

Resistance to weathering

Compressive strength

Vacuum

Radioactive radiation

Free sample box

iglidur sample box with bearing samples and a comparison card.

Typical application areas

Nozzles apply topping to pastries.

Food industry

Glass cutting machine with a linear igus energy chain system for cable and hose guidance.

Glass industry

Textile threads run through an industrial weaving machine.

Textile industry

Contact us

Contact details

rob dumayne
Rob Dumayne

drytech® Director

01604 677240Contact us

Opening hours